Niko Track Roller Bearing

Product Description

The internal design of NIKO track rollers is the same as in single row or Double-row Angular Contact Ball Bearings.  The units can carry axial loads in both directions and, due to the thickness of the outer ring, large radial loads.

These track rollers are available in single and double row design. They are available with straight cylindrical OD or crowned profile OD. The crowned OD is used to reduce the edge stresses caused by possible misalignment errors. The cylindrical OD can provide increased support due to the longer contact profile. There products are used typically on flat surfaces. Some of the most common applications are: 

* Transfer rolls 

* Idler rollers 

* Support rollers 

* Straightening rolls

Track rollers LR 2..NPP, LR 2..RRU 

These single row ball track rollers are available in two different versions. 

* LR2..NPP: cylindrical OD, with contact seals protected by a metal shield. 

* LR2..RRU: crowned OD with contact seals protected by a metal shield, inner ring with increased width to allow additional lubricant storage.

Track rollers LR 52-53..NPPU, LR 52-53..KDD 

These are double rows angular contact ball track rollers. Due to their internal design, they can carry axial loads of large magnitude. They are available in two versions: 

* LR52-53..NPPU: crowned OD, contact seals protected by a metal shield. 

* LR52-53..KDD: cylindrical OD, with metal shields.

The track rollers with profiled outer ring are basically Double-rows Angular Contact Ball Bearings with a reinforced and profiled outer ring. The outer ring profile allows the units to operate on round shafts or other type of profiled raceways. The outer profile can have three different designs; 

* Track rollers with gothic arch groove - type LFR 

* Track rollers with V shaped groove - type RV 

* Track rollers with W profile - type RM

Type RV and RW can be supplied with the pertinent mounting hardware. The largest portion of these products are used as linear guides.

Track rollers LFR, mounting bolts and studs RC/RE

The track rollers series LFR can be used on round shafts with diameter from 4 mm to 50 mm. The contact between track roller gothic arch groove profile and shaft is on two points. This allows the units to carry loads in both axial and radial direction. The track rollers are available with either shields ZZ or contact seals 2RS.

Track rollers RV

The track rollers RV have a groove machined in the outer ring. The groove is V shaped with an included angle of 120 degrees. These units are predominantly used on shafts with diameters from 7 to 20 MM. The contact between track roller and shafts is on two points. In special cases, the units can run on profiled ways. The units are supplied with non contact shields.

Track rollers with W profile, type RM 

The track rollers series RM have grooves machined in the outer ring of the unit with an included angle of 90 degree. They have been engineered to run on profiled steel elements that have identical shape. They can run on either the internal or the external surfaces of the outer ring. They are available with either non-contacting shields ZZ or contact seals 2RS.

LFR 50/4-4 KDD

LFR 50/4-4 NPP

LFR 50/5-4 KDD

LFR 50/5-4 NPP

LFR 50/5-6 KDD

LFR 50/5-6 NPP

LFR 50/8-6 KDD

LFR 50/8-6 NPP

LFR 5201-10 KDD

LFR 5201-10 NPP

LFR 5301-10 KDD

LFR 5301-10 NPP

LFR 5302-10 KDD

LFR 5302-10 NPP

LFR 5201-12 KDD

LFR 5201-12 NPP

LFR 5201-14 KDD

LFR 5201-14 NPP

LFR 5204-16 KDD

LFR 5204-16 NPP

LFR 5206-20 KDD

LFR 5206-20 NPP

LFR 5206-25 KDD

LFR 5206-25 NPP

LFR 5207-30 KDD

LFR 5207-30 NPP

LFR 5208-40 KDD

LFR 5208-40 NPP

LFR 5308-50 KDD

LFR 5308-50 NPP